9/18/2023 0 Comments Convert psi to mpaĭensity of crude oil, Density of fuel oils, Density of lubricating oil and Density of jet fuel as function of temperature.Īs shown in the figures, the change in density is not linear with temperature - this means that the volumetric expansion coefficient for water is not constant over the temperature range. See also other properties of Water at varying temperature and pressure: Boiling points at high pressure, Boiling points at vacuum pressure, Dynamic and kinematic viscosity, Enthalpy and entropy, Heat of vaporization, Ionization Constant, pK w, of normal and heavy water, Melting points at high pressure, Prandtl number, Properties at Gas-Liquid Equilibrium Conditions, Saturation pressure, Specific gravity, Specific heat (heat capacity), Specific volume, Thermal conductivity, Thermal diffusivity and Vapour pressure at gas-liquid equilibrium.įor other substances, see density and specific weight o f acetone, air, ammonia, argon, benzene, butane, carbon dioxide, carbon monoxide, ethane, ethanol, ethylene, helium, hydrogen, methane, methanol, nitrogen, oxygen, pentane, propane and toluene. See Water and Heavy Water for thermodynamic properties at standard condtions. The density of water depends on temperature and pressure as shown below: Note! Temperature must be within the ranges 0-370 ☌, 32-700 ☏, 273-645 K and 492-1160 °R to get valid values. The output density is given as g/cm 3, kg/m 3, lb/ft 3, lb/gal(US liq) and sl/ft 3. The calculator below can be used to calculate the liquid water density at given temperatures. See more about the difference between mass and weight Online Water density Calculator ![]() Γ = 1.940 * 32.174 = 1.940 /(*) * 32.174 = 62.4 0.68948 Megapascal (MPa) Psi : Psi is the abbreviation of pound per square inch, and is widely used in British and American. The density of water is 1.940 sl/ft 3 at 39 ☏ (4 ☌), and the specific weight in Imperial units is In the Imperial system the mass unit is the slug, and is derived from the pound-force by defining it as the mass that will accelerate at 1 foot per square second when a 1 pound-force acts upon it:ġ = 1 * 1 and 1 = 1 /1 In the SI system, specific weight of water at 4☌ will be: G = acceleration due to gravity, units typically and value on Earth usually given as 9.80665 m/s 2 or 32.17405 ft/s 2 Specific weight is the ratio of the weight to the volume of a substance: Pure water has its highest density 1000 kg/m 3 or 1.940 slug/ft 3 at temperature 4☌ (=39.2☏). Symbols, abbreviations, or full names for units of length,Īrea, mass, pressure, and other types.Density is the ratio of the mass to the volume of a substance: You can find metric conversion tables for SI units, as wellĪs English units, currency, and other data. It is the pressure resulting from a force of one pound-force applied to an area of one square inch.Ĭonversion calculator for all types of measurement units. ![]() The pound per square inch or, more accurately, pound-force per square inch (symbol: psi or lbf/in² or lbf/in²) is a unit of pressure or of stress based on avoirdupois units. ![]() The unit is named after Blaise Pascal, the eminent French mathematician, physicist and philosopher. The pascal (symbol Pa) is the SI unit of pressure.It is equivalent to one newton per square metre. The definition of a pascal is as follows: The SI prefix "mega" represents a factor of Psi to MPa, or enter any two units below: Enter two units to convert From: You can do the reverse unit conversion from
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |